Before you begin looking for Aovo Pro Firmware B-01.0.11k download, ensure the following:

Firmware is the low-level software embedded in your Aovo Pro scooter’s electronic control unit (ECU). The version number B-01.0.11k follows a proprietary naming convention used by Aovo’s OEM manufacturer (often based in Shenzhen, China). Decoding the name:

This firmware is specifically designed to optimize the Aovo Pro’s performance, safety features, and battery efficiency. It is not compatible with generic Xiaomi M365 scooters or Ninebot models, despite physical similarities.

This is the recommended method for 95% of users.

Step 1 – Install the App Download “Aovo Pro” from your app store (blue icon with white scooter silhouette). Avoid fake “Aovo Master” or “Aovo Go” apps.

Step 2 – Pair Your Scooter

Step 3 – Check for Firmware Update

Step 4 – Download and Flash

Step 5 – Power Cycle

Q: Can I downgrade from a newer version to B-01.0.11k? A: Yes, usually. This version is often preferred by modders because it is stable and allows for easier modification via SHU compared to some very new "anti-hack" firmwares. However, always ensure the firmware is signed for your specific controller board.

Q: Will this remove the speed limiter? A: No. Official firmware B-01.0.11k keeps the scooter street-legal. It does, however, make the power delivery smoother than older buggy firmware. To remove the limiter, you must use third-party tools after installing this firmware.

Q: Is this firmware safe for the battery? A: Yes, it is official firmware. It includes standard safety protocols for the 36V or 48V battery systems used in the ES80.

B-01.0.11k is a sought-after version for the Aovo Pro electric scooter, primarily used to bypass factory speed limits and unlock a potential top speed of up to 28–30 mph (45 km/h)

. While the official AovoPro app has removed the ability to select this specific firmware, users frequently turn to alternative applications to access it. How to Access and Install B-01.0.11k Because the stock AovoPro app

(black icon) often hides this version, the community-recommended method involves using the (blue icon) or specialized tools. Download 365GO : Install the on your device. The "10% Glitch" Method Connect your scooter and go to Settings > Firmware Upgrade > Available Version B-01.0.11k

is not visible, some users load a different version (like ...13) and force-close the app once the update reaches roughly

Reopen the app; the scooter should remain in "upgrade mode," often causing B-01.0.11k to appear in the "Available Version" list. Complete the Flash B-01.0.11k and allow the update to finish completely. Unlock Speed : Once installed, navigate to Advanced Settings > Speed Limit Value to set the new maximum. Key Considerations & Risks Lights Bug

: This specific firmware version is known for a bug where the physical scooter button may no longer control the lights. In this case, lights must be toggled via the AovoPro app Hardware Limits

: While the software may display 45 km/h, the actual speed is limited by the 36V battery and motor. Most users report a realistic top speed of 19–22 mph (30–35 km/h) under load. Warranty & Safety

The Aovo Pro firmware version B-01.0.11k is a highly sought-after legacy update primarily used by the electric scooter community to bypass factory speed limiters. While newer official versions prioritize safety and stability, this specific build is famous for enabling an "advanced settings" menu that allows users to increase the scooter's top speed to approximately 28–30 mph (45 km/h). Key Features of Firmware B-01.0.11k

Riders often prefer this version because it provides more granular control over the scooter's hardware.

Speed Unlocking: The primary draw is the ability to adjust the "Speed limit value" in advanced settings beyond the standard 19 mph cap.

Disabled Recovery (Regen): Unlike standard firmware, 11k often comes with "rekuperatsiya" (energy recovery) disabled by default, allowing for a smoother "coasting" (freewheeling) feel when you release the throttle.

Custom Parameter Tuning: Users can often tweak acceleration and braking response curves more freely than in newer, locked-down versions. Known Issues & Technical Bugs

Because this is an older or "glitchy" firmware version, it is not without risks:

Lighting Bug: A common issue with the 11k version is that the physical light button on the handlebars may stop working, requiring you to use the AovoPro app to turn the headlight on or off.

Power-Off Glitch: Some users report that the scooter may automatically turn back on immediately after you try to power it down.

Safety Warning: Increasing the speed limit can strain the motor and battery, potentially leading to overheating or "E3" error codes. How to "Download" and Install B-01.0.11k

You cannot typically find this version as a standalone file download on the official AovoPro website. Instead, the community uses a specific method involving the 365GO app, which often hosts legacy firmware lists that the official AovoPro app has removed.

Install the 365GO App: Search for "365GO" (blue icon) on the Apple App Store or Google Play. The official "black icon" AovoPro app generally does not offer the 11k version anymore.

Connect Your Scooter: Turn on your scooter and pair it via Bluetooth within the 365GO app. Firmware Downgrade/Upgrade: Navigate to Settings > Firmware Upgrade. Look for B-01.0.11k under the "Available Versions" list.

Pro Tip: If 11k isn't showing, some users start an update to a different version (like version 13) and force-close the app at 10% to "reset" the firmware mode, then reopen it to see the full list of legacy versions.

Finalize Speed Settings: Once installed, go to Advanced Settings and set the speed limit to your desired value.

Warning: Using unofficial apps or downgrading firmware may void your warranty or "brick" your controller if the process is interrupted. Always ensure your scooter is fully charged before attempting an update. AOVO PRO E-SCOOTER - HOW TO USE THE 365GO APP

Yes, if:

No, if:

Downloading and flashing unofficial firmware may violate local traffic laws (e.g., increasing speed beyond legal limit) and voids the scooter’s CE/FCC compliance. Always wear a helmet, and never flash firmware while charging. The author and this review are not responsible for any damage to your device or personal injury.

Would you like a step-by-step guide with screenshots for flashing using ScooterHacking Utility or a comparison table of Aovo firmware versions?

Aovo Pro firmware B-01.0.11k is a legacy version of the scooter's operating software, widely discussed in community forums for its unique "speed hack" capabilities. While officially superseded, it remains sought after by users looking to bypass factory speed limits on M365 clone models. Firmware Overview

The B-01.0.11k firmware is primarily used as a "speed-unlock" tool for the Aovo Pro M365 clone. Top Speed Unlocking

: Users report that installing this specific version allows the speed limit to be adjusted up to 28 mph (approx. 45 km/h) within the advanced settings of compatible apps. Known Issues

: A common bug in this version causes the physical headlight button on the scooter to stop working, requiring users to turn lights on/off exclusively through the mobile app. Risk of "Fake" Versions

: Some community members warn that certain "11k" versions circulating online only change the speedometer display to show higher speeds without actually increasing the motor's physical output. How to Download & Install Aovo Pro does not host direct

firmware files for manual flashing. Updates are handled through specific mobile applications. Compatible Apps 365GO (Blue Icon)

: Frequently cited as the most reliable way to find B-01.0.11k under the "Available Version" list. AovoPro (Official Black Icon) : Newer versions of the official AovoPro App

often omit these legacy firmware options to comply with safety regulations. Installation Process Download the app from the Google Play Store

Connect to the scooter via Bluetooth (default password is often Navigate to Settings > Firmware Upgrade > Available Version B-01.0.11k to begin the flash. Security & Safety Warnings AOVO Pro no firmware available in app. : r/ElectricScooters 25 Dec 2020 —

The Aovo Pro Firmware B-01.0.11k is a legacy firmware version widely known in the community for enabling a higher top speed on the Aovo Pro electric scooter. Key Features and Details

Unlocked Top Speed: This specific firmware version allows users to increase the scooter's maximum speed to approximately 45 km/h (28 mph), whereas the standard factory firmware typically limits the speed to 25–31 km/h.

Advanced Settings Access: Once installed, an option for a higher "Speed limit value" usually appears under the Advanced Settings menu in compatible apps.

Known Bug: A significant trade-off of this version is a firmware bug where the scooter's front light can only be controlled through the mobile app and cannot be toggled using the physical button on the scooter display. How to Access and Download

This version is typically not available on the official AovoPro Google Play app. According to user reports on Reddit and Imgur, it is often accessed through the following method:

Use the 365GO App: Users frequently download the 365GO app (blue icon) rather than the standard AovoPro app (black icon) to find this firmware version.

Firmware Menu: Within the app settings, it may appear under Firmware upgrade > Available Version.

Downgrade "Trick": Some users report having to start a different update and then cancel it around 10% to "force" the app to display older versions like B-01.0.11k.

Note: Flashing unofficial or legacy firmware carries risks, including potentially "bricking" your scooter or voiding your warranty. Official updates and manuals are available directly from the AOVOPRO Support site. If you'd like, I can help you:

Check if your scooter model is compatible with this specific hack. Find the latest official firmware version for your device.

Troubleshoot connectivity issues with the 365GO or AovoPro apps.

This guide includes the download source, update methods, changelog details, and troubleshooting tips.

No official direct download link exists on Aovo’s own website (which is basic and lacks firmware archives). Instead, the firmware is found via:

⚠️ Warning: No official OTA (over-the-air) update system via an “Aovo Pro” branded app exists for this specific version. Most downloads are user-uploaded.

Yes. Aovo Pro does not charge for firmware updates. Any website asking for payment is a scam.