Alarm Manual Full - Cobra 3195
The above guide is a summary intended to give you a functional understanding of the Cobra 3195 alarm system without reproducing copyrighted text from the official manual. For detailed wiring diagrams, regulatory compliance information, or advanced configuration (e.g., integrating with third‑party home‑automation platforms), you should obtain the full, up‑to‑date manual from the sources listed in section 9.
The Cobra 3195 is part of the legacy 3000 series (similar to the 3193 and 3198 models), which are standard vehicle security systems featuring radio remote control, engine immobilization, and volumetric protection. Core Operation Guide
Arming: Press the large button (A) on the remote key fob. The direction lights will flash twice to confirm the system is armed.
Disarming: Press the small button (B). The direction lights will flash once, and the status LED will turn off.
Emergency Override: If the remote fails, you must use the unique 4-digit PIN code provided on the system's security card. Programming New Remote Fobs
To add a new transmitter (up to 4 per system), follow these sequential steps:
Prepare Remotes: Press both buttons on the remote simultaneously until the LED stops flashing (approx. 10 seconds). The LED will then stay illuminated. Repeat for all remotes you intend to use.
Initialize Mode: Turn the ignition ON and OFF 3 times within 7 seconds. The dashboard security LED will light for 3 seconds. Enter PIN: Immediately after the LED goes out, turn the ignition ON.
Count the LED flashes until they reach your first PIN digit, then turn the ignition OFF.
Turn ignition ON again and repeat for the remaining three digits.
Sync: If the code is correct, the LED remains lit. Press the large button on each remote until the dashboard LED goes out and comes back on to confirm sync. Exit: Turn the ignition OFF and test each fob. Common Troubleshooting
Battery Low: If the remote's LED flashes weakly or the system beeps upon disarming, replace the remote battery.
Trigger History: If the alarm went off while you were away, the status LED will blink in a specific pattern when you disarm: 1 blink: Door or boot opened. 3 blinks: Bonnet opened. 4 blinks: Ignition/hotwire attempt. 5 blinks: Volumetric/motion sensor triggered. Coding new Cobra remote. - Technical Talk
While official printed manuals for legacy products like the Cobra 3195 cobra 3195 alarm manual full
are no longer produced, digital versions and comprehensive guides are available through the Cobra Support Portal Cobra 3195
is part of the 3100 series (often grouped with models like the 3198), sharing core functionality for vehicle security.
Below is a breakdown of the essential operational and technical information found in the full manual. 🛡️ Core Security Features
Perimeter Protection: Monitors door, boot, and bonnet triggers.
Volumetric Protection: Uses ultrasonic sensors to detect movement inside the cabin.
Immobilization: A dual-circuit immobilizer prevents the engine from starting without authorization.
Panic Function: Allows the user to trigger the siren manually via the remote. 🔌 Operational Basics
Arming: Press the main button on the remote; indicators flash twice.
Disarming: Press the secondary button; indicators flash once.
Emergency Override: If the remote fails, you can use a 4-digit PIN code or a touch key to disarm the system manually. 🛠️ Programming & Troubleshooting Diagnostic Flash Codes
If the alarm is triggered, the dashboard LED will flash in a specific sequence to identify the source of the breach: 3 Flashes: Ultrasonic sensor trigger. 4 Flashes: Attempted hotwire/ignition trigger. 5 Flashes: Boot or bonnet circuit issue. Remote Programming To sync a new key fob, you typically follow these steps:
Disarm the system and turn the ignition ON/OFF 3 times within 7 seconds. The LED will flash to signal programming mode.
Press and hold buttons on the new fob for 10 seconds until the system confirms with a flash or beep. The above guide is a summary intended to
💡 Pro Tip: For legacy models, it is highly recommended to view manuals on a desktop computer, as the PDF formatting may not display correctly on mobile devices. Download Product Manuals for your Cobra Device
While a standalone PDF specifically titled "Cobra 3195 Full Manual" is rare due to the system's age, the Cobra 3195 is an older car alarm and immobilizer system that shares nearly identical programming and operational logic with the widely documented Cobra 3198. Core Specifications & Features
Security Type: Old Cobra unit (legacy technology, now often badged as Vodafone Automotive).
Default PIN: The factory default PIN for this series is typically 1111. Key Protections: Volumetric ultrasonic sensors (interior motion detection). Perimetric protection (door, boot, and bonnet opening). Engine cranking inhibition (immobilizer). Emergency override via a unique 4-digit PIN. Essential Operating Instructions
Based on the closely related Cobra 3198 Manual and user guides from ManualsLib, here are the standard procedures:
Arming: Press the large button (often "A") on the remote. Indicators flash twice, the LED illuminates, and doors lock.
Disarming: Press the small button (often "B") on the remote. Indicators flash once, the LED turns off, and doors unlock.
Panic Alarm: Press and hold the "A" button for 3 seconds while the system is armed to trigger the siren.
Deactivating Motion Sensors: (For leaving pets/passengers inside) Arm the system, then immediately press the "A" button again. A beep or flash confirms the ultrasonic sensors are off for that session. Cobra Alarm but no pin number - MotorhomeFun
Complete User Guide for the Cobra 3195 Alarm System The Cobra 3195 is a modular car security system designed to provide comprehensive protection, including perimetric monitoring and ultrasonic interior detection. This guide synthesizes essential operations, programming steps, and troubleshooting tips from official documentation and technical support resources. Core Remote Functions
The system is typically operated via a two-button radio control.
Button A (Large): Arms and disarms the system. Pressing it once locks the doors and activates sensors; pressing it again unlocks the doors and disarms the alarm. Button B (Small): Used for secondary features.
Panic Alarm: Press and hold Button B to trigger the siren manually in an emergency. Fix: The immobilizer is still active
Sensor Exclusion: To leave a pet or person inside, press Button B within 20 seconds of arming to temporarily disable the internal ultrasonic sensors. Emergency PIN Override
If your remote fails or is lost, you can disarm the system using your unique 4-digit PIN code: Cobra 8185 Alarm System Manual | PDF - Scribd
USER INSTRUCTIONS USER INSTRUCTIONS * Car Alarm Immobiliser System. Thatcham M.I.R.R.C. Evaluation No: ... * Radio Key Function. *
Coding new Cobra remote. - Midlands Lotus Owners Club (MLOC)
Note: The Cobra 3195 series is a popular range of vehicle security systems (often sold under brands like Viper, Clifford, or directly as Cobra Atena). Because specific manuals can vary slightly based on the installation configuration in your specific vehicle, this guide covers the standard operations, programming menus, and troubleshooting for the Cobra 3195 system.
Fix: The immobilizer is still active. Insert key, turn ignition ON, press disarm button. If still no start, use valet button: Turn ignition ON, press valet button for 4 seconds until LED turns off.
A: Enter programming mode (ign ON, valet 5 sec). Then press valet button 6 times. Siren chirps 2 times to confirm passive OFF. 1 chirp = passive ON.
Before we dive into custom programming, here are the legitimate sources to download the full original manual:
The Cobra 3195 alarm system has three modes:
Programming
The Cobra 3195 alarm system can be programmed using the keypad or a computer. Programming options include:
Troubleshooting