If your model supports a touchscreen or a specific button combination, try:

Once you successfully reset your MKi9200 without the remote, take these steps to avoid the headache again:

How to Reset Your Parrot MKi9200 Without a Remote If you have lost your remote control or the battery has died, you might find yourself locked out of your Parrot MKi9200 settings. Because this system relies almost entirely on its wireless RF remote for menu navigation, performing a factory reset without it is difficult—but not impossible if you have the right hardware or a bit of patience. The Short Answer: Can You Reset Without a Remote?

Standard factory resets for the Parrot MKi9200 strictly require the remote control to access the Settings > Advanced Settings > Factory Reset menu. However, there are two primary workarounds depending on your car's setup:

Steering Wheel Controls (Unika Interface): If your car uses the Parrot Unika interface to link your steering wheel buttons to the Parrot system, you can navigate the menus without the original remote.

Hard Reboot (Battery Disconnect): While not a "factory reset" that wipes data, disconnecting the unit from power for one hour can resolve some software glitches and "reboot" the system. Method 1: Using the Unika Steering Wheel Interface

If your installer integrated the Parrot system with your car’s factory steering wheel buttons, you can use a specific sequence to enter the menu and trigger a reset.

Enter the Menu: Rapidly press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back.

Navigate to Settings: Once the menu appears on the MKi9200 screen, use the Track Forward button to scroll until you see "Settings".

Access Advanced Settings: Press your steering wheel's Phone/Accept button to enter the menu. Scroll down to "Advanced Settings" and press Phone/Accept again.

Trigger Factory Reset: Navigate to Factory Reset and confirm with the Phone/Accept button. The unit will reboot and clear its memory. Method 2: The "Memory Full" Emergency Reset

If you are trying to reset because you see a "Memory Full" error and cannot pair new phones, some users have reported success with a physical button combination if they still have access to the screen's control box or older firmware versions.

The Command: Press and hold the Green (Answer), Red (End Call), and Center Jog Wheel (if your model has an integrated one) buttons simultaneously for approximately 10 seconds.

The Result: The screen should go blank and emit a beep, indicating that the paired device list has been wiped. Method 3: Troubleshooting a "Dead" Remote

Before giving up on the remote, check if it simply needs a re-sync rather than a full system reset. Often, a remote isn't "broken," it just lost its pairing with the blue electronic box.

Replace the Battery: The remote uses a standard CR2032 battery. Ensure it is inserted correctly and that the metal contacts are touching the battery. Re-pair the Remote: Turn on your car's ignition.

Within the first 2 minutes of boot-up, simultaneously press and hold the Answer (Green), End (Red), and Play/Pause buttons.

Continue pressing them until the screen displays "Pairing Remote". Pro-Tips for Persistent Issues

Wiring Check: If your Parrot forgets settings every time you turn off the car, it likely isn't a reset issue but a wiring problem. You may need to swap the red and orange wires on the Parrot harness to ensure the unit receives constant power for its memory.

Replacement Parts: If the remote is truly lost, note that official replacements are increasingly rare. You may find used units on marketplaces like eBay or specialized retailers like JustCarKits.

Do you have steering wheel buttons available, or are you looking to buy a replacement remote to regain control? JustCarKitshttps://www.justcarkits.co.uk

How to reset a Parrot MKi9200 without the remote - JustCarKits

Resetting a Parrot MKi9200 without the original wireless remote is typically not possible through standard menus, as the remote is the primary way to navigate settings. However, you can use these alternative methods depending on your vehicle's setup: JustCarKits 1. Steering Wheel Controls (UNIKA Interface) If your car has a Parrot UNIKA

interface installed, you can navigate the menu using your factory steering wheel buttons. JustCarKits Access the Menu : Press the following sequence on your steering wheel: Track Forward > Track Back > Track Forward > Track Back Navigate to Settings Track Forward button to scroll to "Settings". Perform Factory Reset Phone/Accept button to enter "Settings". Advanced Settings and select it. Factory Reset and confirm with the The unit will reboot and clear all paired devices. JustCarKits 2. Hard Reset via Power Cycle

While this won't always delete paired phones, it can clear temporary glitches or a "frozen" screen. JustAnswer Disconnect Power

: Remove the car battery terminal or disconnect the Parrot control box (usually hidden behind the dashboard) for at least 10 minutes to allow the capacitors to discharge. Check Wiring

: If the unit "forgets" settings every time you turn the car off, the red (permanent 12V) and orange (ignition) wires may need to be swapped. JustAnswer 3. Firmware Update

Updating the firmware via a USB drive can sometimes force a memory wipe. JustCarKits Prepare a USB stick with the latest firmware from the official Parrot support site

Plug it into the MKi9200's USB cable. If the unit detects the update, it may overwrite existing data and reset the device. JustCarKits 4. Clearing "Memory Full" Errors If you are trying to reset because of a "Memory Full" message but cannot access the menu:

How to reset a Parrot MKi9200 without the remote - JustCarKits

To reset your Parrot MKi9200 without a remote, you can follow these steps. This process might slightly vary depending on the specific model and its firmware version, but for most Parrot MKi9200 units, the following steps should work: