Before attempting the Test Point procedure, ensure you have the following:
The "JMM-AL10 test point" is more than just a set of copper pads on a circuit board; it is a symbol of the delicate balance between consumer technology and engineering infrastructure. It serves as a necessary tool for manufacturing, a critical rescue point for technicians, and a potential vulnerability for security analysts. As smartphones become increasingly sealed and secure, the ability to access these low-level hardware interfaces remains a vital skill in the ecosystem of mobile technology, turning potential electronic waste into functional devices once more.
Search for JMM-AL10 motherboard photos, EDL/EDL test-point guides for Huawei, and UART pinout references for concrete board images and step-by-step examples.
If you want, I can write a longer how-to with step-by-step photos and a parts list — say whether you want "beginner-friendly" (no soldering) or "technician" level (soldering + pogo pins).
Related search suggestions provided.
Under normal conditions, your phone communicates via USB in three main modes:
However, if the bootloader is corrupt, the device is hard-bricked, or FRP is triggered with no way to bypass it via settings, the standard USB connection fails. The phone cannot boot into any functional mode.
Test points force the phone into a low-level download mode (Meta Mode or Qualcomm 9008/HS-USB Mode) by shorting specific pins during power-up. This allows third-party tools (like SP Flash Tool, IDT, or HCU) to detect the device and flash new firmware, bypass screen locks, or remove FRP.
The Huawei JMM-AL10 is a specific model variant within Huawei’s budget and mid-range smartphone lineup from the late 2010s. Known in some markets as the Huawei Nova Smart or a variant of the Honor 6 Play, this device is popular in regions like the Middle East, Africa, and Asia. Like all Android smartphones, the JMM-AL10 is susceptible to software issues: boot loops, hard bricks, FRP (Factory Reset Protection) locks, and failed updates.
When conventional methods (like using the Volume Up + Power buttons to enter recovery) fail, technicians and advanced users turn to a hardware-level solution: the Test Point.
This article provides a deep dive into the JMM-AL10 test point—what it is, where to find it, how to use it, and the risks involved. By the end, you will understand how to force this device into Meta Mode or Download Mode to restore it from the dead.
is the Chinese variant of the Huawei Honor V9 Play (also known internationally as the Honor 6C Pro ). It is powered by the MediaTek MT6750 jmm-al10 test point
processor. Test points on this device are primarily used by technicians to force the phone into a specific "Flash Mode" (MTK Preloader/BROM mode) to bypass Factory Reset Protection (FRP), remove Huawei IDs, or repair a "dead boot" when the device is software-bricked. m.sunsky-online.com 1. Hardware Context & Test Point Usage
Shorting the test point to ground (GND) allows service software like UnlockTool
to communicate with the MediaTek chipset before the system boots, enabling low-level flashing or partition erasing. Key Operations: FRP Bypass: Removing Google or Huawei account locks. Huawei ID Removal: Unlinking the device from a lost account. Dead Boot Repair: Reflashing the device when it does not power on normally. 2. Technical Specifications (JMM-AL10) Model Name Huawei Honor V9 Play / Honor 6C Pro MediaTek MT6750 Octa Core 4GB RAM + 32GB Storage (China Version) Android 7.0 (EMUI 5.x) 3. Procedure for Using Test Points
To access the test points, the device must be partially disassembled:
The is the model number for the Huawei Honor V9 Play (also known as the Honor 6C Pro
in international markets). The "test point" is a physical hardware method used to force the device into MTK (MediaTek) Brom or EDL mode, allowing for low-level software repairs like bypassing FRP (Factory Reset Protection), fixing a dead boot, or flashing firmware. Honor V9 Play (JMM-AL10) Test Point Details Processor: MediaTek MT6750.
Primary Purpose: Used for FRP bypass, screen lock removal, or repairing a bricked device when standard recovery methods (like Power + Volume Up) fail.
Common Software Tools: These tools often require the test point to detect the device in the correct mode: UnlockTool (often cited for Honor series FRP removal). TFT MTK Tool. MRT Key (legacy). General Procedure Huawei Honor V9 Play (JMM-AL10) - DeviceAtlas Huawei Honor V9 Play (JMM-AL10) | DeviceAtlas. DeviceAtlas
The (better known as the Huawei Honor V9 Play or Honor 6C Pro
) requires a specific hardware "test point" to trigger MTK Brom Mode (EDL equivalent for MediaTek chips). This is typically used to bypass FRP, fix "Orange Message" errors, or unbrick a dead device when standard recovery isn't working. Locating the Test Point
To find the physical test point, you must remove the back cover and the internal metal shielding. The test point consists of a single gold contact on the motherboard that must be "shorted" (connected) to the metal shielding or any ground point using tweezers. Identify the Points: On the Before attempting the Test Point procedure, ensure you
motherboard, look for a small gold pin located near the battery connector or the LCD flex cable.
Short to Ground: Use a pair of metal tweezers to touch that specific gold point and a metal shield (ground) simultaneously.
Connect USB: While holding the short, plug the USB cable into your PC.
Verification: If successful, your PC's Device Manager should show "MediaTek USB Port" or "MTK USB Port" under the Ports section. How to "Put Together a Piece" (Step-by-Step)
If you are looking to assemble the device or perform a repair, here is the order of operations:
Internal Components: Ensure the motherboard is seated correctly and all flex cables (LCD, charging port, side keys) are snapped firmly into their connectors.
Battery Placement: Connect the battery flex cable last to avoid shorting any components during assembly.
Shielding & Screws: Replace the metal shields over the connectors and tighten the screws. These are vital as they often act as the "ground" for the test point and protect the board from heat.
Sealing the Back: Align the back cover, starting from the top. Press gently along the edges until you hear it snap into place.
Software Finish: If you used the test point to flash a ROM, you may need to perform a Hard Reset via Recovery Mode (Hold Power + Volume Up) to clear old cache data and ensure a smooth first boot.
Pro Tip: If you're struggling with a Google Lock (FRP), tools like UnlockTool or CM2 are commonly used once the device is in Brom Mode. Under normal conditions, your phone communicates via USB
While there isn't a single definitive long-form article titled "JMM-AL10 test point," various technical resources and guides discuss this hardware entry point for the Huawei Honor V9 Play (JMM-AL10)
. This specific test point is a critical hardware bridge used by technicians to bypass software locks or unbrick devices that no longer boot normally. Technical Context & Purpose
The JMM-AL10 test point is primarily used to force the device into a low-level diagnostic mode (often referred to as MediaTek (MTK) USB Port
) by physically shorting a specific point on the motherboard to the ground. Bypassing Security : Technicians use this point to remove a
or bypass FRP (Factory Reset Protection) when standard software methods fail. Unbricking
: If a firmware update fails and the device is stuck in a boot loop, this hardware method allows for a "Dead Boot Repair" by forcing the computer to recognize the chipset for direct flashing. Software Requirements
: Once the hardware bridge is established, professional servicing tools like UnlockTool are typically required to execute the repair. Physical Location & Process Locating the test point requires disassembling the phone
, which typically involves removing the back cover and metal shields covering the motherboard. Identification
: It is usually identified as a small, circular copper pad on the PCB. On Huawei devices with the MT6750 chipset (like the JMM-AL10), it is often found near the battery connector or the EMMC chip. The Procedure
: A technician typically uses metal tweezers to connect the specific pad to a nearby metal shield (ground) while plugging the device into a PC via USB. Limitations & Risks Hardware Damage
: Opening the phone and shorting pins carries a significant risk of permanent motherboard damage if the wrong points are bridged. Modern Security
: Newer Huawei security patches have made some test point methods less effective