Official Wiko Kite 4g L4020 Stock Rom Install -
Important Note: Flashing a stock ROM will erase all your personal data (apps, contacts, messages). Please back up your device before proceeding. This process is intended to fix bootloops, software issues, or to completely restore the device to its original factory state.
Installing the official Wiko Kite 4G L4020 stock ROM is a robust solution for software-related failures. While the process requires careful driver installation and precise timing, the reward is a clean, fast, and secure smartphone.
Recap of critical steps:
If you follow this guide meticulously, your Wiko Kite 4G will be resurrected from boot loops and bricked states. For further reading, visit the official Wiko support forum or XDA thread dedicated to the MT6739 platform.
Disclaimer: Flashing firmware carries a risk of voiding your warranty or permanently damaging the device if done incorrectly. The author assumes no liability for bricked devices, lost IMEI, or data loss. Proceed at your own risk.
Last updated: March 2025. Compatible with Wiko Kite 4G L4020 (MT6739 chipset) and SP Flash Tool v5.2144+.
This guide details how to install the official stock ROM on the Wiko Kite 4G L4020. This process is typically used to repair "dead boot" issues, fix software hangs, or revert to original factory settings. Essential Prerequisites
Before beginning, ensure you have the following components prepared: Hardware: A Windows PC and a reliable USB cable.
Backup: Back up all personal data, as flashing will erase your device.
Battery: Charge the device to at least 50% to prevent it from shutting down during the process. Step 1: Download Required Files
You will need to acquire three main files specific to Wiko devices:
Wiko USB Drivers: Necessary for the PC to recognize the phone in "Download Mode".
SP Flash Tool: The standard utility for MediaTek (MTK) chipset devices.
Wiko Kite 4G L4020 Firmware: Download the official stock ROM file. If you cannot find it, use the Wiko Customer Area and enter your device's IMEI to get the specific factory version. Step 2: Install Drivers and Prepare Flash Tool
Install the MediaTek VCOM drivers on your PC to ensure connectivity.
Extract the SP Flash Tool zip and run Flash_tool.exe as an administrator.
Extract the Stock ROM firmware folder to your desktop for easy access. Step 3: Loading the Firmware
In the world of early 4G budget smartphones, the Wiko Kite 4G (L4020) was a distinct little traveler. Powered by Android 4.4 KitKat official wiko kite 4g l4020 stock rom install
and a dual-core processor, it promised "stress-free surfing" in the palm of your hand. But like any tech legend, sometimes the software "gets tired," leading to the dreaded "hang on logo" or system crashes. Wiko Mobile
When the system fails, the only way back to life is through the Official Stock ROM installation . Here is the story of how that restoration unfolds. The Preparation
Before the "surgery" begins, three artifacts must be gathered: The Stock ROM
: The pure, original software (firmware) specifically for the L4020 model. The Drivers MediaTek (MTK) USB VCOM drivers
, which act as the bridge between the computer and the silent phone. SP Flash Tool
(Smartphone Flash Tool), the orchestrator of the entire process. The Ritual of Installation
This guide provides the official procedure for installing the stock firmware on a Wiko Kite 4G (L4020)
. Reinstalling the stock ROM is often necessary to resolve software issues like boot loops, "hang on logo" errors, or to restore the device to its original factory state. Pre-Installation Checklist Backup Data : Flashing a stock ROM will erase all user data
(contacts, photos, and messages). Ensure you have backed up important files. Battery Level : Charge your device to at least to prevent it from powering off during the process. : Use the original or a high-quality micro-USB cable. Wiko Mobile Required Tools and Drivers
You will need to download and install the following on your Windows PC: Wiko Kite 4G : Ensure you download the specific firmware for the Smartphone Flash Tool (SP Flash Tool) : This is the standard utility for flashing Wiko devices. MediaTek (MTK) USB VCOM Drivers
: These allow your computer to recognize the phone in "Download" mode. Step-by-Step Installation Guide 1. Install Drivers Install the Wiko USB Drivers
and MTK VCOM drivers on your computer. If using Windows 10 or 11, you may need to disable "Driver Signature Enforcement" first to allow the installation. 2. Prepare SP Flash Tool Extract the SP Flash Tool zip folder and right-click on Flash_tool.exe , then select Run as Administrator 3. Load the Firmware In the SP Flash Tool, navigate to the Click on the Scatter-loading Locate the Android_scatter.txt file inside your extracted Wiko Kite 4G stock ROM folder and select it 4. Start the Flashing Process Ensure the dropdown menu in SP Flash Tool is set to Download Only button (green arrow icon). Power off your Wiko Kite 4G completely and remove the battery if it is removable
Connect the phone to the computer via USB. If the computer doesn't detect it, try holding the Volume Down button while connecting. 5. Complete the Install
Once connected, a red bar will appear, followed by a yellow progress bar as the firmware is written to the device. green ring or "Download OK" message appears, the process is finished.
Disconnect your phone, reinsert the battery, and power it on. The first boot may take several minutes. Troubleshooting Tips Device not recognized : Try a different USB port or reinstall the MTK drivers. Fails at start
: Ensure you are using the correct scatter file for the L4020 model and that the firmware is fully extracted. : If the phone still loops after flashing, try performing a Hard Reset
through Recovery Mode (Volume Up + Power) to clear residual cache. Wiko Kite 4G L4020 firmware file? Wiko Stock ROM Firmware Downloads | PDF - Scribd 16 Dec 2023 — Important Note: Flashing a stock ROM will erase
Installing the official stock ROM on your Wiko Kite 4G (L4020)
is the primary method for fixing software issues like boot loops, system lag, or "bricked" states. This process replaces your current operating system with the factory-stable version provided by Wiko. Essential Preparation
Before starting, ensure you have the following prerequisites ready:
Battery Level: Charge your device to at least 80-85% to prevent it from shutting down mid-process.
Backup: Flashing a stock ROM erases all personal data, including photos and contacts.
Hardware: Use a high-quality USB data cable and a Windows-based PC.
IMEI Note: Keep your original IMEI number handy, as you may need to restore it using an IMEI tool after flashing. Required Downloads Stock ROM Firmware: Download the specific
firmware. You can often find official versions on the Wiko Mobile Support page by entering your device's IMEI.
VCOM Drivers: Install the MediaTek (MTK) USB Drivers so your computer can recognize the phone in "Download Mode".
Flash Tool: Most Wiko devices with MTK chipsets use the SP Flash Tool. Installation Steps
Extract Files: Unzip the downloaded firmware and flash tool into separate folders on your desktop.
Launch Flash Tool: Open the SP Flash Tool folder and run flash_tool.exe as an administrator.
Load Scatter File: In the tool, click on the Scatter-loading button and navigate to your extracted firmware folder to select the file ending in .txt (usually named something like MTxxxx_Android_scatter.txt).
Select Mode: Ensure the dropdown menu is set to Download Only to avoid wiping critical bootloader partitions unless necessary. Initiate Flash: Click the Download button in the tool. Connect Device: Power off your Wiko Kite 4G
completely. While holding the Volume Down or Volume Up button, connect it to your PC via USB.
Monitor Progress: A yellow progress bar will appear. Once finished, a green ring or "Download OK" message will pop up.
Reboot: Disconnect the phone and power it on. The first boot can take 5–10 minutes as the system initializes. Troubleshooting Tips If you follow this guide meticulously, your Wiko
Not Recognized: If the PC doesn't detect the phone, try a different USB port or re-install the VCOM drivers.
Error Messages: If you get a "PMT changed" error, you may need to switch the flash tool mode from "Download Only" to Firmware Upgrade. Download Wiko Stock ROM for all models (Latest Firmware)
Installing the official stock ROM on your Wiko Kite 4G (L4020) involves using the Smartphone Flash Tool (SP Flash Tool) because this device uses a MediaTek chipset. This process will completely erase all personal data, so back up your files before proceeding. Prerequisites A Windows PC: Compatible with Windows 7, 8, or 10.
Wiko USB Drivers: Essential for the PC to recognize your phone in "Flash Mode".
SP Flash Tool: The official utility used to write the firmware to the device.
Official Stock ROM: The firmware package for the Kite 4G L4020, which includes the "Scatter" file. Step-by-Step Installation Guide Official Wiko Kite 4G L4020 Stock Rom - Google Drive
🖱️ Official Wiko Kite 4G L4020 Stock Rom - Google Drive. Google Docs
Maria disabled Driver Signature Enforcement first (since SPD drivers are unsigned):
Then she installed the SPD drivers:
She verified in Device Manager → “Unisoc Phone” or “SPD U2S Diag” appeared.
Flashing a ROM is a safe procedure if you follow instructions, but it requires precision. Gather the following:
Read this entire section before proceeding. Timing is critical.
Post-installation: Check your IMEI by dialing *#06#. If it shows "Null" or "Invalid," you used "Format All" mode by mistake. You will need to restore IMEI using Maui META or a custom backup — a much more advanced procedure.
Maria disconnected the USB, removed the battery (if removable), waited 10 seconds, reinserted the battery, and pressed Power.
The first boot took 5–7 minutes (Android Go optimization). She saw the “Wiko” logo, then “Android is starting…”. Finally, the Setup Wizard appeared.
She skipped Wi-Fi and Google login temporarily, enabled “OEM Unlocking” again (if needed), and restored her backups.